Billboard groove wrapping
2024-09-22 02:47:02⓵How wide is the 1.5mm strip of the 4-fold double bag pull tube?
Hemming width: Divide the pull tube size by 4+1 = hemming width (22s-40M), such as 26s pull tube bag Edge width=26/4+1=7.5mm
Woven hemming pulley
1. 20s pulley hemming effect
Hemming width 5.5mm-6mm
2. Universal pulley 26s---the most versatile pull tube---the most practical pull tube
26s pull tube hemming effect: hemming width 7.5mm
3. 32s, 32M pull tube hemming effect---hemming Width 9mm
4. Knitted hemming pull tube
36M pull tube knitting hemming effect, the general hemming width is 1cm, etc.
The pull tube, also known as the hem curler and edge seamer, is commonly known as the mouthpiece. It is an auxiliary equipment used in sewing machines. The pulley is mainly used for rolling collars, piping, card embedding, welting, hemming, curling, hemming, hemming, and feet in the sewing process of various fabrics (such as various types of clothing, leather, bags, etc.) Drawstrings, stickers, etc. According to different product structures, professional pull tubes such as trousers, trouser waists, earrings, high heads, towels, ropes, pockets, and furs are derived. Some complex processes require special and specific development of the pull tubes.
How to use the hemming pulley:
1. Check whether the feed dog and the tug wheel cooperate, check the pre sser foot and whether the pre ssure of the tug wheel is too tight or too loose. There should be a gap between the pre sser foot and the pulley.
2. The pulley baffle is close to the pre sser foot, so that the stitches produced by the machine will be neat and appropriate.
3. Wear the edging tape correctly: Thread the edging strip into the pull tube. There is a slit in the middle. You can use a needle to pass it through. The tail of the edging strip should be neatly arranged. After pulling it out, fold both sides of the edge strip inwards and pull it out at 90 degrees from the front groove.
4. There is no need to cut the edge strips short in advance, and there is no need to tighten the edge strips during turning. Push the edge of the fabric in the direction of the pull tube with your left hand to ensure that the edge of the fabric is close to the center of the edge strips to pre vent it from falling apart.
Notes
1. Note that there should be a slight gap between the pre sser foot and the pull tube;
2. Pay attention to the different thicknesses of fabrics, which require different pull tubes;
3. Pay attention to the size of the pieces and the pull tube The size of the tube must match;
4. If the strapping strip or the cloth strip passes through the pulling tube, then the cloth strip must be cut with a strapping car, the width is uniform, and the wrapping strength is consistent; it must not be cut while cutting Use an electric trimmer to cut the bed; otherwise it will affect the sewing effect.
Woven hemming pulley
1. 20s pulley hemming effect
Hemming width 5.5mm-6mm
2. Universal pulley 26s---the most versatile pull tube---the most practical pull tube
26s pull tube hemming effect: hemming width 7.5mm
3. 32s, 32M pull tube hemming effect---hemming Width 9mm
4. Knitted hemming pull tube
36M pull tube knitting hemming effect, the general hemming width is 1cm, etc.
The pull tube, also known as the hem curler and edge seamer, is commonly known as the mouthpiece. It is an auxiliary equipment used in sewing machines. The pulley is mainly used for rolling collars, piping, card embedding, welting, hemming, curling, hemming, hemming, and feet in the sewing process of various fabrics (such as various types of clothing, leather, bags, etc.) Drawstrings, stickers, etc. According to different product structures, professional pull tubes such as trousers, trouser waists, earrings, high heads, towels, ropes, pockets, and furs are derived. Some complex processes require special and specific development of the pull tubes.
How to use the hemming pulley:
1. Check whether the feed dog and the tug wheel cooperate, check the pre sser foot and whether the pre ssure of the tug wheel is too tight or too loose. There should be a gap between the pre sser foot and the pulley.
2. The pulley baffle is close to the pre sser foot, so that the stitches produced by the machine will be neat and appropriate.
3. Wear the edging tape correctly: Thread the edging strip into the pull tube. There is a slit in the middle. You can use a needle to pass it through. The tail of the edging strip should be neatly arranged. After pulling it out, fold both sides of the edge strip inwards and pull it out at 90 degrees from the front groove.
4. There is no need to cut the edge strips short in advance, and there is no need to tighten the edge strips during turning. Push the edge of the fabric in the direction of the pull tube with your left hand to ensure that the edge of the fabric is close to the center of the edge strips to pre vent it from falling apart.
Notes
1. Note that there should be a slight gap between the pre sser foot and the pull tube;
2. Pay attention to the different thicknesses of fabrics, which require different pull tubes;
3. Pay attention to the size of the pieces and the pull tube The size of the tube must match;
4. If the strapping strip or the cloth strip passes through the pulling tube, then the cloth strip must be cut with a strapping car, the width is uniform, and the wrapping strength is consistent; it must not be cut while cutting Use an electric trimmer to cut the bed; otherwise it will affect the sewing effect.
Your idea is very good. I guess this small groove is not easy to make. Finally, use glass glue to stick it on the glass, which also has a certain buffering function.
It seems that copper strip edging like this is sold. The tiles on the kitchen cabinets all have edging strips, which are metal.
It seems that copper strip edging like this is sold. The tiles on the kitchen cabinets all have edging strips, which are metal.
