How much does a Shijiazhuang wall advertising construction team cost?
1、What is the process of wall advertising production?
Professional companies like Xinmei Advertising generally use the following methods for wall advertising design:
1. The selection of glue materials must be based on the proportion of each color in the entire advertisement, and the operation process is very standardized.
2． After the advertising production is completed, all finished materials must be poured into the finished barrels according to the color. The brushes and rollers must be put into the corresponding barrels according to the colors; the inner and outer covers of each finished barrel must be Keep it covered to avoid waste or accidents caused by spills.
3． All covered buckets must be covered with inner and outer covers while the car is in motion. In the car compartment, raw materials (including light calcium, lithopone, pigments, rubber powder), finished materials (liquid), rollers, brushes, kegs, plates, and construction workers' clothing must be placed in pieces and in an orderly manner. To facilitate construction and avoid unnecessary waste and trouble.
4． When using the plate, three or four people must pre ss it on the unengraved area at the same time.
5． When the printing plate is completed, one end is put down first, and then the other end is slowly put down when someone below takes it.
6. The layout should be cleaned once every two days at most. When cleaning, it is best to soak it in water for 1-2 hours, then rinse it with water, or brush it clean with a brush. When brushing, be careful to protect the layout.
7. If there are any damaged areas in the edition, clean the damaged areas immediately and then glue them up with self-adhesive tape.
8. The plate is damaged in large areas and is difficult to repair. It must be done no less than two days in advance so that the plate can be supplied in time to avoid affecting the progress of the project.
With such standardized operation steps, the wall advertising design produced by Xinmei Advertising is professional enough. The website www.hbxmad.com has a lot of information about wall advertising, which is very useful.
1. The selection of glue materials must be based on the proportion of each color in the entire advertisement, and the operation process is very standardized.
2． After the advertising production is completed, all finished materials must be poured into the finished barrels according to the color. The brushes and rollers must be put into the corresponding barrels according to the colors; the inner and outer covers of each finished barrel must be Keep it covered to avoid waste or accidents caused by spills.
3． All covered buckets must be covered with inner and outer covers while the car is in motion. In the car compartment, raw materials (including light calcium, lithopone, pigments, rubber powder), finished materials (liquid), rollers, brushes, kegs, plates, and construction workers' clothing must be placed in pieces and in an orderly manner. To facilitate construction and avoid unnecessary waste and trouble.
4． When using the plate, three or four people must pre ss it on the unengraved area at the same time.
5． When the printing plate is completed, one end is put down first, and then the other end is slowly put down when someone below takes it.
6. The layout should be cleaned once every two days at most. When cleaning, it is best to soak it in water for 1-2 hours, then rinse it with water, or brush it clean with a brush. When brushing, be careful to protect the layout.
7. If there are any damaged areas in the edition, clean the damaged areas immediately and then glue them up with self-adhesive tape.
8. The plate is damaged in large areas and is difficult to repair. It must be done no less than two days in advance so that the plate can be supplied in time to avoid affecting the progress of the project.
With such standardized operation steps, the wall advertising design produced by Xinmei Advertising is professional enough. The website www.hbxmad.com has a lot of information about wall advertising, which is very useful.
Generally, when painting walls, the common materials used for painting include cement mortar, mixed mortar, cement gravel mortar, lime mortar, gypsum, mortar, Plain cement mortar, etc., the general materials used for special painting include asphalt, acid-resistant asphalt mortar, general cement perlite, ordinary asphalt mortar, etc. These are all commonly used for painting walls.