Suzhou led advertising light box system

It is more energy-saving, safer and has a longer lifespan than neon lights. A typical "green" light box:
The light source of the LED electronic light box uses a new type of ultra-bright LED. The characteristics of LED are very obvious, such as long life, high light efficiency, no radiation and low power consumption. The spectrum of LED is almost all Focusing on the visible light frequency band, its luminous efficiency can reach 80~90%. It is a typical green lighting source. Most people think that it is a great innovation that energy-saving lamps can save 4/5 of energy, but LED can save 1/4 of energy than energy-saving lamps. This is a great reform of solid light sources. Panel: aluminum-plastic panel.
Controller: dual-channel, five-channel (selected according to customer requirements). (1) The size of the aluminum-plastic panel is 122×244. Calculate the size and use it rationally without wasting it. Use a wallpaper knife to cut the appropriate size.
Go to the art department to engrave the pattern the customer needs and use sticky notes to paste it on the aluminum-plastic panel. superior. (I engraved the hollow characters and used instant spray paint. The effect is better than that of sticky notes. Post-it notes will fade after a year in the sun.) It is more economical to use the hollow characters next time.
(2) According to the font and size of the words, use a pen to mark the distance between the holes in the center of the words. The distance between the pattern lights should be 1.5-2cm. The distance between the lights should be 3cm. It should be flexibly controlled. The denser the better the effect. It can also be made into hollow characters for better effect. (Pay attention to the distance when crossing when marking points)
(3) Use a handheld rotary or engraving machine to drill holes, and clean the burrs after drilling.
(4) Install the lights according to the pattern (+,-) (+,-) for later connection. The lights must be installed in place.
(5) After installation, apply half of the glue on one side of the lamp bead to facilitate connection. The picture below shows the connection status of the running lights. The corners of the lamp can be held together but they must be secure, and it is best to finish soldering them.
(6) The LED lights in each word or pattern are connected in series. Each circuit must have no more than 115 red lights, no more than 73 blue lights, and no more than 80 green lights. When the characters or patterns are too large to exceed the number used, add another loop.
(7) Words and words or patterns and patterns are connected in parallel.
(8) Anti-static work must be done during the production process.
(9) Note that all LED pins must not be short-circuited.
(10) Measure the current of each circuit to ensure that the current is 15-20mA.
(11) Select the number of resistors according to the number of patterned lamp beads, weld the resistors with leads and put them into the yellow wax tube. between any two LEDs in the loop.
(12) Led welding time cannot exceed 3 seconds. (It is best to use a constant temperature soldering iron with a grounding wire)
(13) Connect the controller and watch the production effect. The light box display is normally sealed with a glue stick and then assembled.
(14) The three-in-one (five-way) controller outputs DC 220v. Red is positive. Connect the positive lead of the lamp bead to red, and the negative lead of the light box to yellow. The three green wires are the negative electrodes running through each Color after color. White is the always-on negative electrode.
(15) Drill 1-2 8mm holes for water leakage at the lower end of the light box frame. Drill holes on the edge of the aluminum-plastic plate groove on the side of the aluminum material according to the size of the light box and fix the aluminum-plastic plate with screws to pre vent panel deformation. These are the frame eyes under the light box, two of which are waterproof eyes and the other two are connected to the fixed bracket. These are the frame eyes on the side of the light box to fix the aluminum-plastic plate to pre vent deformation of the frame and corners, and the screws used to fix the side of the frame.
(16) Before installation, a 48-hour aging test (let the light box light up and run for 48 hours) is required to test the reliability of the light box.
(17) The long horn of a single LED is the positive pole, and the short leg is the negative pole. Look at the chip inside the lamp bead with the LED connected. The larger one is the negative electrode and the smaller one is the positive electrode. Compare and observe with a single LED.
(18) For the lamp bead resistor ratio and quantity, please refer to the table in the Taobao controller picture (click to enlarge to view).
(19) It is easier to purchase and contact after bookmarking the store. The store has light box kits with different prices for you to make. I recommend you buy the kit with an aluminum frame. (The aluminum material has been cut for easy assembly)
(20) The controller outputs DC 220v, so be sure to pay attention to safety during the production process. Operation is not possible while power is on.
(21) When making a light box, install the aluminum-plastic plate with printed characters into the frame and drill holes vertically to imitate the form of a bench drill.

1. The control software you are using is wrong. LED Studio 10 is a full-color screen control system, which is mainly used for full-color screen synchronous control. And your LED light box should be a monochrome screen with asynchronous display. So you'd better check which manufacturer the control card on the light box is from, and download the control software from their website. 2. The nine-hole connector is the serial port, a common communication interface for monochrome screens. You must have a serial communication line to connect the serial port connector on the computer and the serial port connector on the control card. If you don't have one, I suggest you buy one. 3. After the software is installed, download the manual and follow the instructions above. I don’t know how to call the control card manufacturer anymore. Was the computer that used to control the light box moved? These things need to be adjusted by LED professional technicians. It would be difficult for you, a layman, to do this to me.

The LED electronic light box controller is a device used to control LED lighting. It can realize a variety of lighting modes. In practical applications, LED electronic light box controllers can be widely used in commercial advertising, exhibition displays, entertainment venues and other fields. Let's take a closer look at the operating steps of the LED electronic light box controller.

Step 1: Preparation

Before using the LED electronic light box controller, we need to pre pare the corresponding equipment and materials. First, we need to pre pare LED light strips, LED controllers, power cords, light strip connectors, light boxes, and some basic tools, such as scissors, screwdrivers, etc. After pre paring these equipment and materials, we can start the next step.

Step 2: Install LED light strips

Before installing the LED light strips, we need to determine the size and shape of the light box and choose according to the size and shape of the light box. Corresponding LED light strip. After selecting the LED light strip, we can install it into the light box. The specific installation method can be adjusted according to different light boxes and LED light strips. Generally speaking, we can use the light strip connector to connect the LED light strip to the power cord.

Step 3: Connect the LED controller

After completing the installation of the LED light strip, we need to connect the LED controller to the power cord. The specific connection method can be adjusted according to different LED controllers. Generally speaking, we can connect the input end of the LED controller to the power line and the output end to the LED light strip.

Step 4: Set the lighting mode

After completing the connection of the LED controller, we can start to set the LED lighting mode. The LED electronic light box controller can realize a variety of lighting modes, such as flashing, breathing, gradient, etc. We can select and set the mode through the buttons on the controller or the remote control. The specific setting method can be adjusted according to different LED controllers.

Step 5: Adjust the brightness and color

After setting the LED light mode, we can also adjust the brightness and color of the LED light. The LED electronic light box controller can adjust the brightness and color, and we can adjust it through the buttons on the controller or the remote control. The specific adjustment method can be adjusted according to different LED controllers.

Step 6: Complete the settings of the LED lights

After completing the settings of the LED lights, we can fix the LED electronic light box controller and install the LED light box. In practical applications, we can adjust and set according to different scenarios and needs to achieve the best results.

The LED ultra-thin light box is an improvement on the ordinary ultra-thin light box. The light source is replaced by a T4 or T5 tube to an LED light bar, and the power supply is replaced by an LED driving power supply. The LED light bar is basically Use 3528 or 5050 patches, basically use 7MIL lights. More energy-saving and ultra-thin.
Category:
1. One type has an aluminum alloy frame. When installing, you will see that there are mounting holes on the aluminum on the back of the light box. Open the cover from the front and install it directly with self-tapping screws. .
2. LED light boxes without aluminum frames are also called crystal light boxes. They are removed from the crystal light box with advertising nails, installed on the wall, and then the crystal light box is aligned with the holes and then fixed.