Parking lot horizontal billboard
How to install outdoor advertising signs after they are designed?
How to install outdoor advertising signs after they are designed? Below, Menoxin briefly introduces the installation steps of outdoor advertising signs
1. Outdoor advertising signs In addition to paying attention to safety issues during the hoisting process, the installation of the signboard should also pay attention to the firmness of the welding and the anti-corrosion work at the joints; during the hoisting and lifting process, attention should be paid to adjusting whether the frame of the billboard is tilted, and continue to adjust until it reaches a safe position. , the whole process is directed by a dedicated person and equipped with a whistle to unify the operation.
2. Clear the installation sequence:
(1) Drilling: Fix the purchased formed iron letters to the appropriate position, use an electric drill to drill: 5MM or 8mm, the spacing is according to the external signboard system. It depends on the height and production cost. Generally, the center spacing of LEDs is: 10-30 mm. The smaller the spacing, the better the effect and the higher the cost.
(2) Insert lights: Clean the drilled holes and put the lights in one by one.
(3) Wiring: first connect in series and then in parallel to the power supply. This step is difficult. Don’t worry. There are reserved wires for each string. Generally, the red wire is connected to the positive pole of the power supply, and the black wire is connected to the LED. The negative terminal of the power supply.
(4) Test aging: After connecting all the LEDs, check and deal with those that do not light up, and then perform an aging test for 24 hours.
(5) Sealing: Fix the LED to the iron sheet.
(6) Test again and install.
3. The installation location of the installation vehicle should be selected based on the criteria of stable geological conditions and no harm to the greening; the lifting height should not be too high or too low, and should be appropriately adjusted according to the height of the lifting firmware and installation needs; use cable wind ropes to adjust The verticality of the column pre vents people from approaching for adjustment, which may cause safety hazards; the theodolite should verify that the verticality of the installation is less than 10mm.
4. Complete the installation of the light frame and other components according to the diagram.
5. Foundation review: Arrange relevant technical personnel to measure and review the foundation before installation. The inspection content includes: the foundation plane must be flat, without cracks, honeycombs, exposed ribs, etc.; the transverse centerline and longitudinal centerline of the foundation It must be vertical; the deviation of the basic outline size should not be greater than 20mm.
1. Outdoor advertising signs In addition to paying attention to safety issues during the hoisting process, the installation of the signboard should also pay attention to the firmness of the welding and the anti-corrosion work at the joints; during the hoisting and lifting process, attention should be paid to adjusting whether the frame of the billboard is tilted, and continue to adjust until it reaches a safe position. , the whole process is directed by a dedicated person and equipped with a whistle to unify the operation.
2. Clear the installation sequence:
(1) Drilling: Fix the purchased formed iron letters to the appropriate position, use an electric drill to drill: 5MM or 8mm, the spacing is according to the external signboard system. It depends on the height and production cost. Generally, the center spacing of LEDs is: 10-30 mm. The smaller the spacing, the better the effect and the higher the cost.
(2) Insert lights: Clean the drilled holes and put the lights in one by one.
(3) Wiring: first connect in series and then in parallel to the power supply. This step is difficult. Don’t worry. There are reserved wires for each string. Generally, the red wire is connected to the positive pole of the power supply, and the black wire is connected to the LED. The negative terminal of the power supply.
(4) Test aging: After connecting all the LEDs, check and deal with those that do not light up, and then perform an aging test for 24 hours.
(5) Sealing: Fix the LED to the iron sheet.
(6) Test again and install.
3. The installation location of the installation vehicle should be selected based on the criteria of stable geological conditions and no harm to the greening; the lifting height should not be too high or too low, and should be appropriately adjusted according to the height of the lifting firmware and installation needs; use cable wind ropes to adjust The verticality of the column pre vents people from approaching for adjustment, which may cause safety hazards; the theodolite should verify that the verticality of the installation is less than 10mm.
4. Complete the installation of the light frame and other components according to the diagram.
5. Foundation review: Arrange relevant technical personnel to measure and review the foundation before installation. The inspection content includes: the foundation plane must be flat, without cracks, honeycombs, exposed ribs, etc.; the transverse centerline and longitudinal centerline of the foundation It must be vertical; the deviation of the basic outline size should not be greater than 20mm.
Identification signs play an important role in our daily lives, such as billboards, parking signs, restroom signs, road signs, and hotel lobby signs, etc. . These signs can be divided into various types according to their shape, production materials and application scenarios. Next, we’ll take a closer look at the types of signage and their uses.
1. Vertical signs
Vertical signs are characterized by their vertical length and are usually used for advertising. This type of signage is very common in shopping malls and other places.
2. Horizontal signs
Horizontal signs are characterized by their horizontal width and are often used for advertising. They are usually attached to the walls of small shops or large buildings.
3. Protruding signs
Protruding signs protrude from the wall of the building, and the part except the back can be used as advertising. This kind of signage is quite common, such as on the front of a shop on the street.
4. Ground column signs
Ground column signs are set up on fixed structures on the ground. The forms include horizontal, vertical or three-dimensional signs. This type of signage is often found in parks and other places.
5. Rooftop signs
Rooftop signs are fixed structures placed on the roof of a building, on which plate or cubic signs are hung or pasted. This type of signage is not uncommon on the roofs of buildings.
Classification by production materials:
1. Wooden signs
Wooden signs are very popular in gardens, zoos, parks and other scenic spots. They offer a natural and traditional feel but are more expensive and susceptible to the elements.
2. Stone identification signs
Stone identification signs are resistant to erosion by natural conditions and have a long service life. Although they are heavy and difficult to work with, stone offers a unique texture and style that no other material can match.
3. Metal identification signs
Metal identification signs are made of aluminum alloy, stainless steel, cold plate, titanium plate, copper plate, etc., and are made by die-casting, etching, baking paint, electroplating and other processes. They are stylish in appearance and have a strong modern feel.
4. Synthetic signage
Synthetic signage includes acrylic panels, fiberglass reinforced plastics, aluminum-plastic panels, PVC panels, sunlight panels, Fron panels, etc. These signs are stylish, simple to construct, and affordable.
5. LED luminous signs
LED luminous signs are the product of scientific and technological progress and are often used in commercial areas. They work great day and night, but are more expensive to maintain.
Classification by application scenario:
1. Tourist attraction signage
2. Educational institution signage
3. Real estate developer signage
4. Public environment signage
br/>5. Commercial real estate signs
6. Hospital institution signs
7. Corporate factory signs
8. Residential area signs
9. Underground parking lot signs
In addition, identification signs can also be classified according to whether they are illuminated or not.
The uses of various types of signage include:
1. Image signage
2. Floor-standing diversion signage
3. Floor index sign
4. Department sign
br/>5. Functional signs
The above are the detailed classification and uses of identification signs. They play an indispensable role in modern society.
1. Vertical signs
Vertical signs are characterized by their vertical length and are usually used for advertising. This type of signage is very common in shopping malls and other places.
2. Horizontal signs
Horizontal signs are characterized by their horizontal width and are often used for advertising. They are usually attached to the walls of small shops or large buildings.
3. Protruding signs
Protruding signs protrude from the wall of the building, and the part except the back can be used as advertising. This kind of signage is quite common, such as on the front of a shop on the street.
4. Ground column signs
Ground column signs are set up on fixed structures on the ground. The forms include horizontal, vertical or three-dimensional signs. This type of signage is often found in parks and other places.
5. Rooftop signs
Rooftop signs are fixed structures placed on the roof of a building, on which plate or cubic signs are hung or pasted. This type of signage is not uncommon on the roofs of buildings.
Classification by production materials:
1. Wooden signs
Wooden signs are very popular in gardens, zoos, parks and other scenic spots. They offer a natural and traditional feel but are more expensive and susceptible to the elements.
2. Stone identification signs
Stone identification signs are resistant to erosion by natural conditions and have a long service life. Although they are heavy and difficult to work with, stone offers a unique texture and style that no other material can match.
3. Metal identification signs
Metal identification signs are made of aluminum alloy, stainless steel, cold plate, titanium plate, copper plate, etc., and are made by die-casting, etching, baking paint, electroplating and other processes. They are stylish in appearance and have a strong modern feel.
4. Synthetic signage
Synthetic signage includes acrylic panels, fiberglass reinforced plastics, aluminum-plastic panels, PVC panels, sunlight panels, Fron panels, etc. These signs are stylish, simple to construct, and affordable.
5. LED luminous signs
LED luminous signs are the product of scientific and technological progress and are often used in commercial areas. They work great day and night, but are more expensive to maintain.
Classification by application scenario:
1. Tourist attraction signage
2. Educational institution signage
3. Real estate developer signage
4. Public environment signage
br/>5. Commercial real estate signs
6. Hospital institution signs
7. Corporate factory signs
8. Residential area signs
9. Underground parking lot signs
In addition, identification signs can also be classified according to whether they are illuminated or not.
The uses of various types of signage include:
1. Image signage
2. Floor-standing diversion signage
3. Floor index sign
4. Department sign
br/>5. Functional signs
The above are the detailed classification and uses of identification signs. They play an indispensable role in modern society.