∩ω∩How to calculate the color gusset boards and keels used in an advertising plaque?
It depends on whether you have a vertical gusset plate or a horizontal gusset plate. The gap between the keels is generally 0.5 to 4 centimeters. A gusset plate is 8.5 centimeters. A gusset plate plus a gap times the number of strips. Add a buckle plate to get a close size. The gap is generally 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 4.0. It is recommended that you use horizontal buckle plates and vertical keels. ,, make a double-layer shelf with one support about one meter, one support and one keel. The gusset plate is made 5.05 meters, with an overlap of 10 cm in the middle. Note that the keels must be consistent in height, and the gap is close to the customer's requirements. There is a gap between one more gusset plate and one less one. Not much money,
First of all, consider the customer's requirements for plaques and other materials. But we should also give customers reasonable suggestions, which should be determined based on local climate conditions and temperature changes. Otherwise, some materials will expand and contract with heat and easily deform and fall off. Dimensions provided by customers may not be accurate. The production of company plaques should be measured on-site so that changes in the installation environment can be seen, and the cost should also be taken into consideration. Since the customer's time is limited, the content to be met during the construction period must be designed, and the customer must be repeatedly determined and calibrated. If customers are more open-minded, they will effectively save time. If the client doesn't have any ideas, it will take a while.
1. There are many ways to install company plaques, which need to be determined based on the installation environment and panel materials. Naturally, the needs of the customers also need to be considered. Generally speaking, the installation environment does not require too many workers. The steps for making and installing a company plaque are related to the above. In addition, the customer's subjective concept is also important. The most important thing is not whether the design effect is satisfactory, but whether the customer agrees.
2. Specific steps: plan the content, select the font, and print the content. Cut the printed fonts, stick them on the board with a glue stick or transparent tape, and use a carving knife to dig out the removed parts of the fonts. All dug out. Sand it with sandpaper, trim the details, sand it clean, and round the corners. Select Paint and paint the lettering and surrounding area with color. Wait for the color to solidify. After solidification, it is slightly polished, trimmed, and painted with wood wax oil to get the final product.
Extended information:
Classification of signs
1. Form
1. Horizontal signs: The entire proportion is relatively long horizontally. Usually the entire surface is used as advertising signage. It can usually be seen on the walls of small shops and large buildings.
2. Vertical signage: The entire proportion is relatively long vertically. Usually the entire surface is used as advertising signage.
3. Protruding sign: A sign that protrudes from the wall of a building and uses the entire surface except the back or both sides as an advertising carrier.
4. Ground column signs: horizontal, vertical, and three-dimensional signs marked on certain fixed structures on the ground.
2. Materials
1. Smooth signs: Signs with oily and very smooth surfaces or surfaces.
2. Signs made of luminous materials: Use luminous material signs (what we usually call neon lights).
3. Acrylic sign (acrylic): A sign that uses acrylic material as the main material of the board.
1. There are many ways to install company plaques, which need to be determined based on the installation environment and panel materials. Naturally, the needs of the customers also need to be considered. Generally speaking, the installation environment does not require too many workers. The steps for making and installing a company plaque are related to the above. In addition, the customer's subjective concept is also important. The most important thing is not whether the design effect is satisfactory, but whether the customer agrees.
2. Specific steps: plan the content, select the font, and print the content. Cut the printed fonts, stick them on the board with a glue stick or transparent tape, and use a carving knife to dig out the removed parts of the fonts. All dug out. Sand it with sandpaper, trim the details, sand it clean, and round the corners. Select Paint and paint the lettering and surrounding area with color. Wait for the color to solidify. After solidification, it is slightly polished, trimmed, and painted with wood wax oil to get the final product.
Extended information:
Classification of signs
1. Form
1. Horizontal signs: The entire proportion is relatively long horizontally. Usually the entire surface is used as advertising signage. It can usually be seen on the walls of small shops and large buildings.
2. Vertical signage: The entire proportion is relatively long vertically. Usually the entire surface is used as advertising signage.
3. Protruding sign: A sign that protrudes from the wall of a building and uses the entire surface except the back or both sides as an advertising carrier.
4. Ground column signs: horizontal, vertical, and three-dimensional signs marked on certain fixed structures on the ground.
2. Materials
1. Smooth signs: Signs with oily and very smooth surfaces or surfaces.
2. Signs made of luminous materials: Use luminous material signs (what we usually call neon lights).
3. Acrylic sign (acrylic): A sign that uses acrylic material as the main material of the board.
