The whole process of installation of super large advertising light box
⑴I just bought an advertising light box online. How do I install it? ? ? ?
Tips for fixing the light box in the front door of the store
We will introduce the method of fixing the light box in the front door of the light box.
1. First determine the location of the light box installation, and determine the installation method according to the actual situation and the type of light box.
2. Measure the size: Determine the fixed point for installing the light box based on the position of the mounting holes on the back of the light box or the actual size on site.
3. Fixed light box:
A) The on-site wall is made of aluminum-plastic plate, wood board, iron plate, etc., which can be directly fixed with self-tapping screws;
B) The on-site wall is made of cement or brick For walls, you can first use an impact drill to drill holes, and then fix them with expansion screws;
C) The on-site walls are ceramic tiles, marble, glass, etc. You can use a glass drill bit to drill through the surface first, then drill expansion screw holes, and then fix them. The light box may be glued.
D) For light boxes that need to be hoisted or suspended on site, after selecting the installation location, determine the fixed point for installing the light box according to the actual size of the light box installation hole, then install the hanging hardware and connect the ground wire.
4. Wiring: Normally, the outlet end of the power cord of the light box is on the back. If the power supply on site is on the back of the light box, you can cut off the plug of the power cord, connect it directly, and tie the power connector tightly with insulating tape; If the power supply is outside the location where the light box is installed, the outlet line of the light box power supply can be connected to the edge of the light box, and then a three-phase plug can be inserted into the corresponding power socket;
5. Fix the light box: Open the upper cover of the light box, and Install at the positive fixed point (that is, use an electric drill to drill holes for the power cord at the base of the light box, reinstall the power cord, and use a level to adjust it to a horizontal state);
6. Turn on the power and light, and clean the surface of the light box.
Remarks: Liangxin light guide plate ultra-thin light box uses electronic ballast, which is prone to induced electricity. Please pay attention to the ground wire during installation for safety.
The light box door is a very good billboard, and the effect is very good.
We will introduce the method of fixing the light box in the front door of the light box.
1. First determine the location of the light box installation, and determine the installation method according to the actual situation and the type of light box.
2. Measure the size: Determine the fixed point for installing the light box based on the position of the mounting holes on the back of the light box or the actual size on site.
3. Fixed light box:
A) The on-site wall is made of aluminum-plastic plate, wood board, iron plate, etc., which can be directly fixed with self-tapping screws;
B) The on-site wall is made of cement or brick For walls, you can first use an impact drill to drill holes, and then fix them with expansion screws;
C) The on-site walls are ceramic tiles, marble, glass, etc. You can use a glass drill bit to drill through the surface first, then drill expansion screw holes, and then fix them. The light box may be glued.
D) For light boxes that need to be hoisted or suspended on site, after selecting the installation location, determine the fixed point for installing the light box according to the actual size of the light box installation hole, then install the hanging hardware and connect the ground wire.
4. Wiring: Normally, the outlet end of the power cord of the light box is on the back. If the power supply on site is on the back of the light box, you can cut off the plug of the power cord, connect it directly, and tie the power connector tightly with insulating tape; If the power supply is outside the location where the light box is installed, the outlet line of the light box power supply can be connected to the edge of the light box, and then a three-phase plug can be inserted into the corresponding power socket;
5. Fix the light box: Open the upper cover of the light box, and Install at the positive fixed point (that is, use an electric drill to drill holes for the power cord at the base of the light box, reinstall the power cord, and use a level to adjust it to a horizontal state);
6. Turn on the power and light, and clean the surface of the light box.
Remarks: Liangxin light guide plate ultra-thin light box uses electronic ballast, which is prone to induced electricity. Please pay attention to the ground wire during installation for safety.
The light box door is a very good billboard, and the effect is very good.