Quick installation tips for billboards
发布:寸伯渺
- ⑴How to install light box billboard
- ⑵How to install billboards with dry-hanging marble on exterior walls
- ⑶、How to fix outdoor advertising cloth?
Light box signs, also known as light box billboards, are billboards made of plexiglass with fluorescent tubes or neon tubes inside. They are mainly used to display advertisements in the glass, so how to install light box signs? What's better?
Generally speaking, light box billboards are mainly installed outdoors, and are more suitable for roads, streets, movie theaters, exhibitions, commercial districts, stations, airports, docks, parks, etc.; in addition , with the development of ultra-thin, silent, and environmentally friendly light box billboards, small ultra-thin light boxes can also be used indoors, including some large supermarkets, hypermarkets, banks, beauty salons, buildings, etc. that use light box billboards, and the advertising effect is very good good.
2. How to install light box billboards
Light box signs are a good billboard with good advertising effects. However, the installation of light box billboards will be more troublesome than the installation of ordinary billboards. The following is an introduction to light box signs. Installation method:
1. Determine the installation location
First determine the installation location of the light box signboard, and determine the installation method according to the actual situation and type of light box.
2. Measure the size
Determine the fixed point for installing the light box according to the position of the mounting hole on the back of the light box or the actual size of the site.
3. Fix the light box
Choose different methods according to different wall types: aluminum-plastic panels, wood panels, and iron panels can be fixed directly with self-tapping screws; cement or brick walls need to be punched with an impact drill first, and then used Expansion screw fixation; for tiles, marble, glass and other walls, you need to use a glass drill bit to drill holes on the surface, then drill out the expansion screw holes, and then fix the light box or use glue; some light boxes are suspended or hoisted, after selecting the installation location , determine the fixed point for installing the light box based on the actual size of the light box mounting hole, then install the pendant and connect the ground wire.
4. Wiring
The outlet end of the power cord of an ordinary light box is at the back. When the power supply is located at the back of the light box, cut off the power cord plug, connect it directly, and use insulating tape to fix the power connector; if the power supply is installed at the position of the light box Alternatively, the outlet wire of the light box power supply can be connected to the edge of the light box, and a three-prong plug can be inserted into the power socket provided.
5. Adjust the light box
Open the upper cover of the light box and use an electric drill to drill the power cord on the base of the light box, reinstall the power cord, and adjust it to level and level so that it is installed at a fixed point.
6. Turn on the power supply
Clean the surface of the light box billboard and turn on the power supply before use.
3. Precautions for installing light box signs
1. When the size of the light box sign is large, there needs to be an internal support structure.
2. If the light box billboard is made of acrylic board, it is best not to fix it with screws. It should be bonded with special adhesive or embedded in the board to fix it.
3. There should be heat dissipation holes on the side of the light box.
4. When installing light box billboards, try to choose a method that is easier to install and dismantle, so as not to cause trouble later.
1. The dry-hanging method is also known as the empty hanging method. It is a new construction technology in current wall decoration. This method uses metal pendants to hang the facing stone directly on the wall or hang it on the steel frame without grouting and pasting. The principle is to set main stress points on the main structure, and fix the stone on the building through metal pendants to form a stone decorative curtain wall.
2. Install the horizontal angle steel frame after the horizontal joints of the marble: Determine the location where the billboard is to be installed, remove the stone as a whole at the fixed point, and fix the advertising frame with angle steel welding. The advertising rack must be connected to the steel structure with an angle steel of more than 30 degrees. When positioning, try to allow the advertising rack to cover the space left by removing the stone.
Extended information:1. Clear the installation sequence: column hoisting → billboard frame installation → billboard surface installation → sporadic component installation.
2. Foundation review: Arrange relevant technical personnel to measure and review the foundation before installation. The inspection content includes: the foundation plane must be flat, without cracks, honeycombs, exposed ribs, etc.; the transverse centerline of the foundation and The longitudinal centerline should be vertical; the basic outline size deviation should not be greater than 20mm.
3. The installation location of the installation vehicle must be selected based on the criteria of stable geological conditions and no harm to the greening; the lifting height should not be too high or too low, and the height of the lifting firmware and installation needs should be adjusted appropriately; use cables The wind rope adjusts the verticality of the column to pre vent personnel from approaching for adjustment, which may cause safety hazards; the theodolite should be used to verify that the verticality of the installation is less than 10mm.
4. When installing billboards, in addition to paying attention to safety issues during the hoisting process, you must also pay attention to the firmness of the welding and the anti-corrosion work at the joints; pay attention to adjusting the billboard frame during the hoisting and lifting process. Whether to tilt or not, adjust continuously until it reaches a safe position. The entire process is directed by a dedicated person and equipped with a whistle to unify the operation.
5. Complete the installation of the light frame and other components according to the picture.
If there is a base plate, it is usually tightened from the four sides with ropes. Ordinary small billboards do not have a base plate in the middle. In this case, it is best to use special glue for inkjet printing commonly used on the market. In order to achieve the best viscosity, the following conditions must be met: the billboard should not be too far away from the wall, and the normal distance should be within 1 meter. When bonding, wrap a circle of spray-painted cloth strips around the billboard, double The surface must be fully glued and fixed with 3 seconds glue first. Flattening a picture is a small technical task, and it's best to have someone show you how to do it. First fix the two corners on one side, then on the other side, fix the tightening point on the other two corners, fix the middle, and then the middle of the opposite side. After everything is fixed, if it looks flat, repair it. The pre mise is that every movement must be stretched tightly (except for the first point), and finally it is reinforced.
The outdoor printing fabric is a light box sign fabric composed of two layers of PVC and one layer of high-strength mesh cloth. It is divided into two types: internal lighting and external lighting. Scope of application: indoor and outdoor advertising signs, digital inkjet printing, screen printing, car body awnings, decorative partitions, membrane structures on building ceilings, etc. Width: 1m-3.2m. The material of the inkjet cloth: high-density woven cloth of PP (polypropylene) material, which is the same material as the colorful striped cloth used for wind and rain protection, but the latter is covered with film. Glass fiber should not be used. Glass fiber is generally used in industries such as machine-made asbestos tiles as reinforcement. Inkjet printing cloth generally comes in a roll of 100 meters, and one roll weighs about 100 kilograms. Inkjet printing cloth of different quality levels comes from different raw materials. The thickness of the silk and whether it is high-strength silk are all very important factors. PBC is made in a variety of ways, and the differences in the content of each chemical element will also affect the UV resistance, mildew resistance, and thermal deformation of the inkjet fabric. On the PVC coating, applying an auxiliary transparent acrylic coating is also an option, which can protect the PVC coating.
以上就是关于Quick installation tips for billboards的全部内容,希望能够帮到您。
版权声明:本文来自用户投稿,不代表【威海广告网】立场,本平台所发表的文章、图片属于原权利人所有,因客观原因,或会存在不当使用的情况,非恶意侵犯原权利人相关权益,敬请相关权利人谅解并与我们联系,我们将及时处理,共同维护良好的网络创作环境。
大家都在看
-
广告牌led广告灯
广告牌LED广告灯是一种新型的户外照明设备,具有多种优点和特点,以下是关于广告牌LED广告灯的详细介绍:特点1.高亮度:LED广告灯采用高亮度LED芯片,能够提供明亮的照明效果,即使在
-
昆明宣传栏广告牌价格
工厂宣传栏应该如何设计不锈钢标牌造厂:展览标牌、楼层标牌、铜板、部门标牌、蚀标牌、标牌、宣传栏、文化展览标牌、地铁、机场车站、发标牌、立式信息标牌、楼层车牌、企
-
业主怎么向物业要电梯广告费
根据法律规定小区电梯广告收入归谁?根据法律规定,住宅电梯广告收入归业主所有。由于本节的主要是公共利益,公共利益是通过使用社区的一些公共设施来实现的,应当为全体业主所
-
广告牌四周灯效果图
广告牌的种类有哪些?广告牌的类型如下:1路牌广告路牌广告主要设置在中心区域,位置越好,行越多。所以所产生的广告效果也更强。因此,路标的具体环境是道路,对象是
-
地平线4怎么看撞了多少广告牌
《极限竞速地平线4》全广告牌位置一览难点广告牌收集技巧说明在《极限竞速:地平线4》中收集广告牌可以为玩家增加影响力励和快速移动折扣。该游戏的地图比较大,为了方便玩家
-
广告牌灯箱定时器时间怎么改
路灯定时器怎么设置开灯时间1.2随时间调整,关闭时间按有效时间到有效时间。此时主面板上会显示关灯时间。扩展信息:杂散控器功能功能1.误差小,稳定性强。2.3.
-
橙色广告牌配什么颜色底板
橙色广告牌镶边什么颜色好看黑色、白色、灰色。黑色:橙色和黑色是比较经典的组合。2:白色和橙色的搭配比较清新简洁,适合需要强调广告的场合。3:灰色和橙色的搭配比较低
-
摆摊充电led广告灯牌可挂墙壁
一般灯牌多少钱一个?发标牌的价格根据材质和款式的不同而有所不同。一般最基本的发标牌价格在200元左右。专业灯牌,目前采用2面PVC板材,草帽形广角LED灯。所有LED灯都应
-
高速公路广告牌8米宽高2米设计
隧道结构概述隧道横截面由方形和抛物线构成。方形部分:8米,宽2米。抛物线部分:与方形顶部相连,形成隧道顶部的曲线。
-
上海广告牌诚信经营
租赁广告牌文?1.安全和舒适是我们的首要任务。2.出租安全舒适。3.安全快捷,可以安心自驾出行。4.多种即用型型号。5.不管租不租,反正我是租的。