The whole process of small billboard installation
- ⑴How to install light box billboard
- ⑵How to install LED billboards
- ⑶、How to fix outdoor advertising cloth?
Light box signs, also known as light box billboards, are billboards made of plexiglass with fluorescent tubes or neon tubes inside. They are mainly used to display advertisements in the glass, so how to install light box signs? What's better?
Generally speaking, light box billboards are mainly installed outdoors, and are more suitable for roads, streets, movie theaters, exhibitions, commercial districts, stations, airports, docks, parks, etc.; in addition , with the development of ultra-thin, silent, and environmentally friendly light box billboards, small ultra-thin light boxes can also be used indoors, including some large supermarkets, hypermarkets, banks, beauty salons, buildings, etc. that use light box billboards, and the advertising effect is very good good.
2. How to install the light box billboard
The light box sign is a good billboard with good advertising effect. However, the installation of the light box billboard will be more troublesome than the installation of ordinary billboards. The following is an introduction to the light box sign. Installation method:
1. Determine the installation location
First determine the installation location of the light box signboard, and determine the installation method according to the actual situation and type of light box.
2. Measure the size
Determine the fixed point for installing the light box according to the position of the mounting hole on the back of the light box or the actual size on site.
3. Fix the light box
Choose different methods according to different wall types: aluminum-plastic panels, wood panels, and iron panels can be fixed directly with self-tapping screws; cement or brick walls need to be punched with an impact drill first, and then used Expansion screw fixation; for tiles, marble, glass and other walls, you need to use a glass drill bit to drill holes on the surface, then drill out the expansion screw holes, and then fix the light box or use glue; some light boxes are suspended or hoisted, after selecting the installation location , determine the fixed point for installing the light box based on the actual size of the light box mounting hole, then install the pendant and connect the ground wire.
4. Wiring
The outlet end of the power cord of an ordinary light box is at the back. When the power supply is located at the back of the light box, cut off the power cord plug, connect it directly, and use insulating tape to fix the power connector; if the power supply is installed at the position of the light box Alternatively, the outlet wire of the light box power supply can be connected to the edge of the light box, and a three-prong plug can be inserted into the power socket provided.
5. Adjust the light box
Open the upper cover of the light box and use an electric drill to drill the power cord on the base of the light box, reinstall the power cord, and adjust it to level and level so that it is installed at a fixed point.
6. Turn on the power supply
Clean the surface of the light box billboard and turn on the power supply before use.
3. Precautions for installing light box signs
1. When the size of the light box sign is large, there needs to be an internal support structure.
2. If the light box billboard is made of acrylic board, it is best not to fix it with screws. It should be bonded with special adhesive or embedded in the board to fix it.
3. There should be heat dissipation holes on the side of the light box.
4. When installing light box billboards, try to choose a method that is easier to install and dismantle, so as not to cause trouble later.
If there is a base plate, it is usually tightened from the four sides with ropes. Ordinary small billboards do not have a base plate in the middle. In this case, it is best to use special glue for inkjet printing commonly used on the market. In order to achieve the best viscosity, the following conditions must be met: the billboard should not be too far away from the wall, and the normal distance should be within 1 meter. When bonding, wrap a circle of spray-painted cloth strips around the billboard, double The surface must be fully glued and fixed with 3 seconds glue first. Flattening a picture is a small technical task, and it's best to have someone show you how to do it. First fix the two corners on one side, then on the other side, fix the tightening point on the other two corners, fix the middle, and then the middle of the opposite side. After everything is fixed, if it looks flat, repair it. The pre mise is that every movement must be stretched tightly (except for the first point), and finally it is reinforced.
The outdoor printing fabric is a light box sign fabric composed of two layers of PVC and one layer of high-strength mesh cloth. It is divided into two types: internal lighting and external lighting. Scope of application: indoor and outdoor advertising signs, digital inkjet printing, screen printing, car body awnings, decorative partitions, membrane structures on building ceilings, etc. Width: 1m-3.2m. The material of the inkjet cloth: high-density woven cloth of PP (polypropylene) material, which is the same material as the colorful striped cloth used for wind and rain protection, but the latter is covered with film. Glass fiber should not be used. Glass fiber is generally used in industries such as machine-made asbestos tiles as reinforcement. Inkjet printing cloth generally comes in a roll of 100 meters, and one roll weighs about 100 kilograms. Inkjet printing cloth of different quality levels comes from different raw materials. The thickness of the silk and whether it is high-strength silk are all very important factors. PBC is made in a variety of ways, and the differences in the content of each chemical element will also affect the UV resistance, mildew resistance, and thermal deformation of the inkjet fabric. On the PVC coating, applying an auxiliary transparent acrylic coating is also an option, which can protect the PVC coating.